Digico SD7 Manual do Utilizador

SD7 Operation Manual0-1User Manual - Getting StartedTo be read in conjunction with the SD Series Software ReferenceUser Manual Version D for Software

SD7 - Getting Started1-61.3.6 Channel Types ...The SD7 has 4 different channel type

SD7 - Getting Started1-71.4 Hardware Configuration1.4.1 Connections ...Detailed

SD7 - Getting Started1-81.5 Software ConfigurationThe SD7 has a default setup which means that the new user need not get involved in configuring the d

SD7 - Getting Started1-9To adjust any of the channel allocations, touch on the associated channel count box, and either enter a number using the pop-u

SD7 - Getting Started1-10The section below the graphical rack picture allows configuration of either the cards or slots and sockets (including customn

SD7 - Getting Started1-11The Optocore ID is set at the top of the on screen Network panel and should be as follows:For Optocore V220:First console A E

SD7 - Getting Started1-121.5.8 Manual Conforming of Racks...With a Rack selected in the left hand port sel

SD7 - Getting Started1-131.5.9 Rack Sharing...In a multi-console system where Ra

SD7 - Getting Started1-141.5.10 Assigning Faders to the Worksurface...If, after a Session Restructure, you find that newl

SD7 - Getting Started1-151.6 Saving and Loading Sessions1.6.1 Save As New File ...When y

SD7 Operation Manual0-2Copyright © 2014 Digico UK LtdAll rights reserved.No part of this publication may be reproduced, transmitted, transcribed, sto

SD7 - Getting Started1-161.7 Audio SyncTo access the Audio Sync Panel, touch the Setup Menu button, followed by Audio Sync. The following window will

SD7 - Getting Started1-171.8 Routing Basics1.8.1 Selecting Inputs & Outputs...All channel input, o

SD7 - Getting Started1-18Note also that the console views all routes as a single list. Therefore, if the left signal is connected to the lastsignal in

SD7 - Getting Started1-191.9 Channel Processing1.9.1 Dynamic EQ...The EQ secti

SD7 - Getting Started1-201.9.2 Multiband Dynamics ...The dynamics are accessed by touching t

SD7 - Getting Started1-211.9.3 Auxiliaries ...The auxiliaries can be accesse

SD7 - Getting Started1-221.10 The MatrixTo open the Matrix Inputs panel, touch the Matrix button on the Master Screen Menu. The window that opens all

SD7 - Getting Started1-231.11 Control GroupsAny number of input channels and output channels can be connected to one or more of the 36 possible Contro

SD7 - Getting Started1-241.12 Multi-channel formatsIf you are working in Surround, or using another multi-channel format, you can create LCR, LCRS and

SD7 - Getting Started1-251.13 Solo SetupThe SD7 Solo panel is accessed from a button at the top of the Master Screen. Some of the controls on this pan

SD7 Operation Manual0-3Contents1.1 The Console ... ...1-11.2 Manual Over

SD7 - Getting Started1-26

SD7 Operation Manual0-41.12 Multi-channel formats... ...1-241.13 Solo Setup...

SD7 - Getting Started1-11.1 The ConsoleThe Digico SD7 consists of a worksurface with dual redundant audio engines and a range of onboard inputs and ou

SD7 - Getting Started1-21.3 Before You StartThere are certain general operating principles and terms that should be understood before continuing to us

SD7 - Getting Started1-31.3.2 Layers and Banks ...The SD7's worksurface is divided

SD7 - Getting Started1-4To the right of the Master Panel is a single encoder marked Touch-Turn (shown below). This is used to access any rotarycontrol

SD7 - Getting Started1-5The controls to the right of the Channel Strip panel allow the Assigned channel to be adjusted:The top half of the channel wor